As the saying goes, three -point shooting, seven -point lines, and ball lines are still very important for badminton.If you want to be good, you must first benefit your instrument. Once you are on the court, the choice of badminton lines is very important.When choosing a badminton line, you should choose according to your badminton racket type, requirements, and play needs.So, how to pull the badminton racket?Here are precautions when you introduce the badminton rackets.
Badminton racket pull line method
1. Examination shooting
1. New shooting; check whether the surface of the racket is intact, whether the attachment is complete or whether there is a quality hazard.
2. Old shot; check whether the nursing rubber particles are defective, and whether there is a frame crack in the shooting frame.
3. Fixed the pound; see if the number of pounds required by the customer exceeds the pounds guaranteed by the manufacturer above the label.
4. Cut the wire; please cut the broken line of the broken line.
(Vertical 1, horizontal 11, vertical 1, horizontal 12, need to be cut at the same time), and finally cut: vertical 2, horizontal 10, vertical 2, horizontal 13, vertical 3 ...
2. Set up
1. Tightened the frame at 6 points and 12 oclock on the frame fixing frame.
2. Tight the four -point clamping carrier to the frame wall.(It is appropriate to avoid the occurrence of early deformation just as the edge of the tight frame.)
3. Make sure that the six points of the four -point clamp, the fixed rack of the frame and the frame are kept on the same level.
4. Depending on different models, the slave frame is 6 and 12 oclock out of the pillar gong pole or plastic pads 0.5 ~ 1mm.Causes concave or paint phenomenon in the paint surface.
5. After adjusting the tightness of the thread clip, you can first use the line with the same diameter of the line to do the preliminary test.
6. Adjust the required pounds.
Third, threading, pulling line
1. The vertical line starts with the middle box of the racket, and wears it on both sides and pulls the lines on both sides in order to ensure that the racket is the same tension at the same time and achieve the consistent force.When wearing it to the lower 9 holes, jump to the lower 12 holes to penetrate (two holes in the middle), wear out from the top 11, then penetrate from the top 10 holes, wear 10 holes from the bottom, and pass through the vertical line.
2. Pass the horizontal line from 9 holes in the lower 5-6 (uncertain) holes in the knot, and start pulling the line in the lower 10 holes.Pounds, when wearing 11 holes (uncertain), reduce the number of pounds by 2 pounds, restore the pound of the vertical line), and finally jump to the upper 4-5-6 holes (uncertain).
Fourth, knot
When pulling the last line that needs to be knotted, it increases by 10 % on the basis of the number of vertical lines to prevent the knot from falling out.
Badminton racket line model selection
The ultra-fine line diameter of BG-6: 0.66mm is composed of high-density fiber woven to the extreme slender ball line, providing excellent shock absorption performance and a keen sense of ball.
BG-65: 0.70 mm wire diameter, the core material is multi-layer resin, the outer material is chemical synthetic resin braid fiber, good elasticity, excellent abrasion resistance and economy, the largest sales volume, which has always been the largest of badminton masters.Praise.
BG-66: The core material is a multi-layer resin, and the outer material is a chemical synthetic resin to make a bundle fiber. The 0.66mm ultra-fine line diameter makes it have excellent elasticity and shock absorption performance, and the strike sounds are crisp and loud.
BG-70PRO: 0.70 mm line diameter, the core material is multi-layer resin, the outer material is ovaricized synthetic resin brain fiber, which allows it to maintain a stable stable featron tension for a long time, which is most suitable for strong players.
BG-80: 0.68 mm line diameter, the core material is the new high coefficient "VECTRAN" fiber, the outer material is ovate resin to make a bundle fiber. It has excellent elasticity and explosive power when hitting the ball.Essence
BG-85: 0.67 mm line diameter, the core material is the new high coefficient "VECTRAN" fiber, the outer material is a multi-layer resin bundle fiber, good elasticity, high-speed hitting and powerful, and excellent pumping effect is excellent.Essence
BG-65TI: 0.70 mm wire diameter. The core material is chemical synthetic multi-layer resin, and the outer material is a resin beam fiber. The fiber surface uses a new type of titanium hydrogen alloy coating technology.The ball feels hard and powerful, suitable for high feather line tension.
BG-68TI: 0.68 mm wire diameter. The core material is chemical synthetic multi-layer resin. The outer material is a resin beam fiber. The fiber surface uses a new type of high-density hydrogen titanium coating technology.Sentence and hard.
BG-75TI: 0.70 mm wire diameter. The core material is chemical synthetic multi-layer resin, and the outer material is a resin beam fiber.Hitting the ball is hard and powerful, the most suitable for offensive players.
BG-88Ti: 0.69 mm wire diameter, the core material is the new high coefficient "VECTRAN" fiber, the outer material is ovaricized synthetic resin braid fiber, which is excellent, the most suitable for ball control and technical players.
NBG-95: The new nano-wire, the application of nano technology and the 0.69 mm wire diameter of nanomal technology in 2006, which make it very good in durability, rebellion, and play.The concaveness of the surface horizontal and vertical section of the racing line is reduced by 15%, and the unity of high rebound and high durability is obtained.
Precautions for badminton rackets
1. Do not use waxes to coat the line. The wax will greatly reduce the overall tension of the shooting frame. When hitting the ball, it is easy to slide the line, causing unstable ball control, and the hitting point is deviated.In addition, the upper wax is very harmful to the liner. The clip cape cannot run the pound.
2. Do not use the head of the machine to knot. You can use a pointed mouth pliers, knot clamps, and blocking clips to knot. Use the head to knot to drive the knot line to drive the vertical line to form a reverse force.Disted.
3. It is difficult to wear when wearing the horizontal line to the horizontal and vertical lines. You can use a pointed mouth pliers to pinch the head through the thread. If you expand the holes with an awl, you should specially be careful of the awl to arbitrage.

Related tags： Sports