I believe that every family will have a balcony. We dry up clothes to dry on the balcony. The clothes drying rod is a must -have supplies, but because some clothes drying rods are not set when decorating, it is too high to dry.The family will install a hand -shaking drying rack.It is a hand -shaking drying rack, and it is very convenient to imagine that using it.However, some friends dont know how to shake the drying rack installation method, which is embarrassing.Let ’s introduce the following editors, so that everyone can know the installation method of shaking the drying rack.
Hand -shaking drying rack installation method one
1. Installation of shaking handiches:
The hand -shaped hand is generally installed on the right side of the balcony, because the right hand is the most convenient, and it is generally 120 cm from the ground. The specific height is determined by the users height.Pay attention to fixing the expansion screws of the hand.
2. Installation of the top seat:
On the top of the installed balcony, use a steel ruler to measure the diameter of the lighting on the top of the balcony, and then mark it between 15 and 30 cm on both sides of the light.Then measure the distance between the edge of the balcony and the mark to determine the width of the top seat.Then measure the length of the balcony, centered on the light, and determine the equal division of 80 to 100 cm on both sides of the lighting rod length. There are 4 cross points from the measuring distance from the width. The cross point is the installation position of the top seat of the hanger.Then use an electric drill drill, and fix 4 top seats with the expansion screws after drilling the hole.
Note: Two top seats that rely on shaking hands are the activity end.The other two top seats are fixed seats, with two rounds of activity seats. The activity seat must be installed in front.
3. Install corner:
The corner can be installed on the top of the wall or the top of the balcony, and the corner distance is 50 to 70 cm. In the middle of the top seat of the activity, the corner must be triangular.
4. Steel wire connection:
There are 2 steel wires inside a drying rack. First, one end of a steel wire through the corner bearing wire groove, the active wheel bearing wire slot on the top seat of the active end, and then pass through the bearing wire slot of the fixed top seat.Keep the wire and the ground vertically, then put the top cover from the wire from the steel wire.The other end of the steel wire passes through the corner bearing steel wire groove and another hole, and then passes through another active wheel bearing steel wire groove. Pay attention to keep the wire and the ground vertically, and then enter the top cover from the steel wire, and the top seat cover.The other steel wire installation method is the same.
5. Dry to dry rod:
At the end of each steel wire, wear a hanging ball, and knots in the hanging ball; then pull the ball until the top seat is held, pull the steel wire from the corner, become a double -shaped steel wire, stuck on the hand shake.One end; relax the wire in the hand shake, the ball drops the ball, pass the drying rod through the hanging ball, and then tighten the pores of the hanging ball to nail the screw; finally install the head on both ends of the drying pole.
In fact, it is not difficult to say. Five steps can complete the installation of hand -shaking clothes racks. I believe that everyone will not worry about installation problems according to the method of Xiaobian.
Method of the installation method of hand shake and drop the drying rack two
1. Open the outer packaging of the lifting drying rack, check the parts of the drying rack after checking without damage. General parts include: corner, fixed cover, hanging ring, hand shake, expansion screw, handle, wire rope, ascent plug, pulley, pulley, pulleyshelf.
2. First install the hand shake, install the hand shake at any end of the two ends of the corridor, measure the location of the hand shake to be installed, and generally install it at a distance of one meter to two meters.Location, then use the marking pen to mark the holes that need to be perforated, then remove the hand -shaped machine, use electric drill to punch, install the swelling glue plug, and fix the hand shake to fix it;When it comes out, when shaking the wire rope, you need to pull the wire rope to avoid random lines until the handle cannot move.
3. Determine the installation position of the wheel rack. The pulley rack is the four support points installed on the ceiling. The two -sliding wheel rack near the corner, the end is a single -sliding wheel rack. Generally, a single slide rack is taken as an example.The distance from the walls on both sides should be greater than 27 cm, and the distance between the two single -sliding wheel racks should be greater than 45 cm, and the general distance between the single -slip rack and the double -slit rack is 2m, but the installation environment is the final condition.Determine the labeling after the installation position, mark the hole position, and then punch the hole position.
4. After playing the holes, assemble the expansion screws with the four pulley frames, and the assembly is as shown in the figure.
5. After assembling, install the two double -slip racks and the two single -slip racks on the horn position.
6, assemble the corner with the expansion screw.
7. Determine the installation position of the corner. The position of the corner must be perpendicular to the position of the hand shake, which is 90 degrees.
8. After determining the installation position, mark the punch and install the assembled corner.
9. In the first step of wearing a steel wire, disassemble the steel wire, hold one end of the two steel wires inside, and first put them into the corner.
10. Then pass the two ends of the wire rope through one of the double -slider racks. The two steel wire ropes are parallel and do not entangle. Pull one end of the wire rope worn from the double -slider rack to the position of the hand shake.The device, the other steel wire rope is the same as the same operation in front, and then hang the buttons on the end of the steel wire rope from the hand shake to the tail of the corner steel wire rope, and the other is the same operation.Install the fixed cover.
11. Install the suspension ring, cut the just -earned steel wire at 4 ends of the wire, and then pass it through the ring and tie it.
12. Install the clothes drying rod and fix the four rings on both sides of the two clothes rods, respectively.
At this time, the installation of the lift drying rack has been completed. The summary of the editor is that the steps of wearing a wire rope are relatively complicated. You need to read it carefully. Do n’t connect it wrong. You do n’t find the childrens shoes of the clothes rod to install the master shoes.
Tips for clothes
Avoid state
You can dry clothes in the shade and ventilation until half -dry, and then put it in the sunny and evening sunlight, so as to protect the color of the clothes.Especially many clothes such as hairy, silk, nylon, etc., after direct light, often become yellow.
White clothes
White clothing should be put away immediately due to the strong absorption. This can prevent the fluorescent dye in the laundry absorb a large amount of sunlight after a day of sunlight.
Dark clothes
To avoid fading, when clothes are drying, you can turn your clothes over and turn inside to dry.
Cotton/hemp
In the sunlight, the strength is almost not decreased, or it decreases slightly but does not deform, so it can be placed directly in the sun.However, in order to avoid fading, it is best to facing the opposite side.
Chemical fiber
Because acrylic fibers are easily yellowed after exposure; under the sun exposure of nylon, patella, and artificial fibers, fibers are prone to aging; polyester and Wei Lun will accelerate the fibers optical cracking under the action of sunlight, affecting the life span of the fabric.Therefore, the chemical fiber clothes can be hung directly on the hanger, so that it is naturally dehydrated and dry.
Silk
It is not advisable to dry water and dehydrate with the water machine. You can use a towel to squeeze out the water, and then hang the clothes to dry it in a cool place.In addition, because of the poor performance of silk clothing, it cannot be exposed directly in the sun, otherwise it will cause the fabric to fade.
After cleaning the sweater, it is generally very deep, and it is easy to deform when drying clothes.Therefore, after washing, you can put the clothes into the net pocket and hang it in a ventilated place.If possible, you can dry them on other objects, and pay attention to avoid exposure and baking.
Wool
After washing, put it in a cool and ventilated place to dry it naturally, and facing the opposite side.Because the surface of woolen fiber is scales, the external natural oily membrane is given the wool fiber with a soft luster.If it is exposed to the sun, the surface oily film will deteriorate due to the oxidation effect of high temperature, which will seriously affect its appearance and service life.
Wiring clothes to dry clothes
After the clothes are removed in the washing machine, it is best to take it out immediately, because the clothes are placed in the dehydration machine for too long, which is easy to fade and wrinkle.Secondly, after removing the clothes from the dehydrator, it will immediately throw a few times to prevent wrinkles.In addition, after drying shirts, hoods, sheets, etc., light shooting can also help prevent wrinkles.

Related tags： Houseware