Electronic locks in the field of security technology prevention, electronic password locks with anti -theft alarm function instead of traditional mechanical password locks, overcoming the shortcomings of mechanical password locks and poor security performance, so that the password lock is technical or performance in terms of performance or performanceThe top is a great step.So, how to install an electronic lock?What tools do I need to install electronic locks?Lets take a look together.
Electronic lock installation notice
1) Fingerprint door locks are a high -tech product. The use environment of the door lock plays an important role in the normal use of the door lock, especially in the environment where dust or air contains highly corrosive substances, which will greatly affect the door lock.Normal use.Therefore, it is recommended that you have to install the door lock after the room has been decorated to facilitate the normal use of the door lock and extend the life of the door lock.
2) After the door lock installation and debugging are completed, please register the administrator in time to facilitate your better use of your fingerprint door lock. We recommend that when registering your fingerprint, it is best to backup a fingerUnder accidents such as wear can open the door normally.
3) The quality of the fingerprint door lock directly affects the normal and service life of the door lock. It is recommended to install it with experienced personnel, and strictly install it in accordance with the companys installation standards, and must not be changed at will.
4) Fingerprint locks are the perfect combination of world -tip biometric technology with traditional electronic door locks. To make you better feel its convenience and advanced, please carefully and random reading operation manuals before use.The steps in this article may need to use the following tools L electric diamond, random 8mm, 16mm, 20mm, 25mm drill bit.L woodworking chip L flat -mouth screw knife l plum blossom groove screw knife l straight ruler line drawing pen.
Electronic lock installation step
Select the suitable installation location, and put the random installation template on the door to ensure the flatness of the paste.
1. Line: marked the high line on both sides and door frames on the door frame according to the size shown in the installation mold, marked the contour lines and round hole center lines on the door, and drilled out the installation holes according to the marking size.You can start installing the door lock.
2. Drilling: 4 installation holes in 8mm with electric drilling, and 34mm in diameter of 34mm and 20mm square shafts. Use electric drills and wood -cutting 25x50mm square holes 95x30x5mm concave.
Install the lock core: Check whether the pores of the lock body are consistent with the installation hole, pass the lock core, and then use the screws to fasten.
Outer lock body: Put the waterproof rubber pad, wear a wire through perforation and the position of each installation hole, first use 2 screws, pass the installation board in the door, and fix the front door components on the door in the lower part.
3. Put the back lock body: connect the connected wire of the front and rear locks according to the correct interface, insert the wire into the sockets socket in different connections, and then connect the knob square shaft, and ensure that the front and rear locks are reliable and the lock core is reliable.Connect, and finally fix the hind body on the door with a screw.
4. Install the battery and battery cover: Put the battery in the correct positive and negative electrode into the battery box, and close the battery cap.
5. Function detection: After the installation is completed, refer to whether all the relevant functions of the user manual detection lock are normal.
Precautions for electronic lock installation
Because the door opening method is different, the open hole position is not the same, so you must first determine which hole positions on the installation model need to be opened before the door opening method.
Pay special attention: Lock the front and rear body wire, the direction of the socket and the plug to ensure that the connection is correct.First determine the installation height of the lock before installation. After determining the height, the installation mold is pasted in the corresponding position, and then draws the position that needs to be opened with a pencil.
When you draw the holes, install the mold folding edge to be vertical with the door frame, otherwise it will cause the lock body to not be vertical with the door after installation.
The lock core is generally required to be installed in the middle of the door thickness.
After the door frame is opened, you must clean up the wood chips or other miscellaneous objects in the hole to prevent the door from falling into the lock when the door is vibrated.
Keep your lock tidy body: Do not fall into the lock body from the lock body from the lock body, causing the short circuit or other components from the lock body to fall into the lock body.Link core installation: After the lock core is installed in the installation hole, the surface of the lock core cannot be higher than the surface of the door frame, it is best to be on the same plane.
Installation of the gusset: The pitch position and the position of the lock tongue must be corresponding. If the corresponding is not good, the door will loosen or cannot be closed.Installation of the lock: The screw must be in place, and there must be no gap between the lock body and the door.The connection of the wire: The connection of the wire must be correct, and the connection is firm, otherwise the door lock will not work properly.
Eligibility criteria:
The lock body is perpendicular to the door frame and has no dumping; there is no loose phenomenon after the door is closed; the hand is flexible; the reset is normal; the lock tongue pops up normally without the phenomenon;In order to close or the door rebound, it is judged to be installed in unqualified); the functions are normal.

Related tags： Houseware