The balcony at home is generally installed with clothes rods to facilitate daily drying clothes. So, how should the balcony drying rod be installed?Put up the clothes rod or first install the balcony ceiling?What are the precautions for the installation of the balcony drying rack?
Pay attention before installation of the balcony lift dryer
Many friends mistakenly thought that after the ceiling was completed, the drying rack was installed. In fact, this approach was incorrect, mainly because the part of the ceiling could not be loaded, and in general, the clothes on our drying rack were very heavy.Therefore, the drying rack needs to be fixed on the top (the structure of the floor, the beam, etc.) to install it safely.If you accidentally put on the ceiling and then the drying rack, this is a repair problem. Everyone knows that the drying racks are combined with sliding rails and steel wires. Sometimes it is inevitable to derail.If you want to disassemble, you should be a furnishings if you do n’t dry it.In addition, the wire wire and base of the lift -up drying rack will be exposed to the pulley, and it will appear messy.
Most of the modern family balcony ceiling uses aluminum pins or PVC gushing boards. Generally, it is about 10cm from the top surface of the balcony smallpox. In this case, it needs to be installed with it automatically.The automatic lift drying rack is fixed by the top of the ceiling by the expansion screw, and the balcony ceiling itself does not have great load -bearing capabilities.Therefore, if the ceiling of the balcony is on the balcony ceiling, the automatic lifting drying rack cannot be fixed on the ceiling keel. The good installation method is to pass through the ceiling ceiling decoration, and directly fix the steel wire on the ceiling floor.The width of the balcony is generally 45-50 cm. The particularly width balcony can be appropriately relaxed; the spacing of the two hangers of each drying pole is generally about 1.5-2 meters.
It should be noted that the location of the hand shake is selected. Determine the position before installing the drying rack.Generally, it does not affect the entry and exit of the personnel; it is not close to the sink; the connection of the two two -wheel top bracket cannot be installed.The installation height of the hand shake should be about 100 cm from the ground, and the corner is installed on the corner of the hand shake, or on the ceiling near the corner directly above the corner of the hand shake.On the wall.
How to install the balcony clothes rod
1. Installation of shaking hands
Handiculum is generally installed on the right side of the balcony to facilitate habitual use. It is generally 120cm from the ground, and it is determined according to the user height.Fixed with expansion screws.
2. Installation of the top seat
On the top of the balcony installed on the clothes drying rod, measure the diameter of the lighting on the top of the balcony with a steel ruler, and then make a installation mark between 15cm-30cm on both sides of the lamp (the length is determined by the balcony size).Then measure the distance between the mark and the edge of the balcony, and determine the width of the top seat according to this distance.Then measure the length of the balcony with the lamp as the center, and determine that the two sides of the lamp are divided into 80cm -100cm according to the length of the clothes drying rod, and there are four cross points from the measuring distance from the width. These four cross points are the installation position of the top seat of the hanger.After the position is determined, use an electric drill drill. After the drill is drilled, the four top seats are fixed with the expansion screws (if the bar is more than the conventional size, this distance is adjusted accordingly).
Note: The two top seats on the corner of the hand are the activity end.The other two top seats are fixed seats. The difference between them is that the activity seat is in two wheels, and the activity seat must be installed in front.
3. Installation corner
The corner can be installed on the top of the balcony or the top of the wall, and the corner distance is 50--70cm. The triangle (45 degrees angle) must be formed in the middle of the top seat of the event.drawing.
4. Steel wire connection
There are two steel wires in a set of clothes drying rods. Take one first. First, one end of the steel wire through the corner bearing steel wire groove, and then pass through the active wheel bearing wire groove on the top seat (located on the upper part of the top)Then pass through the bearing wire trough with a fixed top seat to allow the steel wire to vertically on the ground, and then put the top cover from the wire from the steel wire, and the top seat cover.The other end of the steel wire also passes through the corner bearing steel wire groove and another hole, and then pass through another activity wheel bearing wire groove (below the same seat) of the activity seat, so that the wire is perpendicular to the ground, and then puts the top cover from the steel wire into the wire into the wire into the wire into the wire into the wire., Card the top seat cover.The other steel wire installation method is the same.
5. Dry and connect
At the end of each steel wire, wear a hanging ball and knots in the hanging ball; then pull the hanging ball to the top of the top. At this time, pull the wire from the corner, just become a double -shaped steel wire, stuck on the hand on the handOne end of the shake; relax the steel wire in the hand shake, drop the ball to drop, pass the drying pole through the hanging ball, and then rotate and fix it at the hole of the hanging ball, nail the screw; finally install it on both ends of the drying pole on the ends of the drying pole.Cover.
Precautions for installing the balcony drying rod
1. Many people think that the balcony ceiling should be installed first, and then the drying rod and curtain slide rail should be installed. In fact, this view is wrong.The correct approach is to install the clothes rod first, and then perform the balcony ceiling.
2. When installing the lift drying rod, if you want to make a balcony ceiling, you must first use the steel bars to fix the ceiling on the ceiling. Make sure that the length of the steel bar can expose the ceiling L to 2 cm.After the hanging, install the clothes drying rod on the reinforced bars, so that it is convenient for future maintenance and maintenance.It should be noted that the ceiling is not bearing, and the clothes on the clothes drying rod are heavier, and it must be fixed on the floor or beam, so that it is safe.Therefore, no matter what method is adopted, structural load must be adopted.The balcony drying rod is installed.
3. The installation point of the lift drying rod is four top pulleys, as well as a corner and a hand -shaped machine. These need to be fixed on the ceiling and wall.Specifically, the four top pulleys should be installed on a plane, and there must be no obstacles between them, so as not to affect the sliding of the wire rope.The wall of the ceiling and the wall of the installation hand shake should be a right angle, so as to ensure that the wire rope has always been at the center of the pulley during the sliding process, so that the pulley is uniformly stressed and rotated normally.
The above is an article on the installation method of the balcony drying rod and the precautions for installation of the balcony drying rod.Know.The balcony drying rod brings great convenience to our lives.Now people pay most attention to health, so dressing is also a healthy aspect. If clothes can be illuminated by the sun, then sterilization can be sterilized, so the clothes after the sun will be more healthy.I hope everyone can pay attention to it.

Related tags： Houseware