Electric push cutting is a common household haircut tool, hairdressing tools.Electric push cuts are generally composed of fixed pushing teeth, activity push, adjusting the handle, shell, and electrical components installed in the shell. When used, the power is required to AC.So, what is the use of electric push cutting?What is the method of electric push cutting?Lets take a look today.
How to use electric push scissors
(1) If you trim longer hair, it is best to cut the long hair with manual scissors first, and then use electric push to trim.
(2) Installation and disassembling electric push, be sure to disconnect the power switch, otherwise, it is easy to be cut.
(3) When the noise of the electric push is large or the blade is violently vibrated, a ingot screw next to the electric push can be loosened backwards and check whether the screw screw is too loose., But dont press too tightly.
(4) If the hair is rolled across the hair to form three white roads, this means that there is a leak, which is caused by the small vibration force or no vibration.
(5) Add lubricating oil to the upper blade often to reduce the dry friction and excessive heat between the upper and lower blades.
(6) The blade and gaps of the upper and lower blades are easy to hide dandruff, dandruff, dust or other debris. After each use, use a small hair brush to clean.Due to the curing of hair debris and skin oil, it will hinder the movement of scissors and its sharpness, so it should often be brushed off the debris that remain on the blade.
(7) Do not use electrical push cuts in the bathroom or humid occasion, or use a warm hand insert (pull) plug, otherwise it is easy to shock.For the electric push shear of the 220V power supply using the three -core wire, it is necessary to ensure that the socket end of the ground wire is well matched with the plug.
(8) After use, cut off the power and apply some rust oil on the upper and lower blades. The lubricant should be wiped off next time.If you do n’t use it for a long time, you should apply the lubricant, put it on the protective cover, and store it in the box properly.
(9) Sprinkle, Tian Naishui or other volatile chemical agents should be used to clean and clean.
Electric push cuts and purchase methods
(1) Beautiful appearance, light weight, flexible operation, effort, small vibration, low noise.
(2) The blade hardness is good, the scissors are sharp, brisk and freely when cutting, and there is no phenomenon of hair and hairpin.
(3) The moving range of the blade is not less than 1.5mm.The contact surface of the lower blade should be smooth and smooth.The blade should have a variety of specifications such as coarse, medium, and detailed.
(4) Electric push and shearing insulation must be good and reliable, and there should be no leakage.At the same time, the full load load is used for 8 minutes, closed 4min, and then used for 8min continuously.The temperature rise of the lower blade should not be higher than 15 ° C, and the temperature of the electromagnetic coil should not be higher than 65 ° C.
(5) When used, noise should not be greater than 70dB, that is, people should not make people feel annoying.
(6) When the voltage fluctuation soil is 10 %, it can also be used normally.
(7) Plastic and electric parts should be bright and bright on the surface, without numbness, spots, bubbles, deformation and other phenomena.
(8) The gap between the on -shell should not exceed 0.75mm.
(9) The back groove of the lower blade is vertical and clear, the altitude is in the middle, there is no gap and obvious defects, and the tip of the tooth should be smooth.
(10) The surface of the metal parts (except the upper and lower blades) should have an anti -corrosion protective layer, and the plating layer is fine and fine, and there should not be defects such as spots, linen, pinhole, bubbles, shelling and dew.
Common fault machine processing method of electric push shear
1. The coil is hot and burned out
(1) The use time is too long, within the allowable range, new coils should be replaced and conditions are improved.
(2) Long -term power -on -time iron rolling.The position of the head should be cleaned up or adjusts the position.
(3) Coil insulation or coils vibrate to short -circuits in the internal turbine.Replace new coils and fix it.
2. There is no sound of the speed power supply, no action
(1) The dripping contact fatigue is not flexible.Replace the switch or replace the touch film.
(2) The power cord is twisted and the wiring head is loose.Replace the power cord or fix the fixed head, and wipe the mud at the connector.
(3) Dandruff in the switch causes the power to break the power.Apply a brush to remove dandruff.
3. Electromagnetic sound is connected to the power supply, but the electrical push is not moved
(1) There are too many dandruff on the upper and lower blades, and the dandruff should be removed.
(2) The screws are too tight.The above and lower blade should be re -adjusted in the tightness of the looseness of the blade.
4. Dont eat hair
(1) The angle of the corner head changes.Adjust the angle of the corner head to about 45 degrees.
(2) The screw of the corner head is loose.Tighten the corner screw.
(3) Regulate screws and ingot screws loose.The screw should be adjusted based on the shawl head vibration.
(4) The gap between up and down JJ J1 is too large.New adjustment) J film screw.
5. Do not spine
The blade blade is worn.Rehabilitation blade or replace the new blade.
6. Like a loud noise
The screw spring adjustment is not good.Update and adjust each screw.
7, leakage
(1) The coil leads to line insulation damage.Re -process the line insulation.
(2) Wirling damage and internal moisture of the power cord standpoint.Replace the new power cord and re -insulated treatment.

Related tags： Houseware