The silk machine is to electrize the manual tube snail twisted panel before 1980.It makes the pipe thread processing easier and fast when the pipeline is installed.Reduce the labor intensity of the workers in the pipeline installation workers.Before operating the setting machine, you first need to understand the operating procedures for the set of wires, so as to better use the tools and complete pipeline processing.What are the main points of the daily maintenance of the silk machine operation?The following editors will introduce the operating procedures and maintenance common sense of the silk machine.Lets take a look together!
How to use manual wire machine
Because the manual wire machine is easy to carry, it does not need to use power, but is used in large quantities for field operations.Here, I will briefly put the hand -in -the -handed wire operating steps for you:
1) The pipeline is fixed on the bracket, and a certain length is left on the front end for silk.
2) The dental mold head that matches the pipeline size is installed on the spinal wheel handle, and the filament machine is connected to the pipeline.
3) Start the silk: the left hand is pushing the tooth mold head, and the handle of the handle is operated on the right hand to rotate the tooth mold clockwise (the right hand thread).
4) After eating the pipes in the plate, you can release your left hand and get in your own lines on your own.At this time, you can add some cut oil.
5) When the edge of the pipeline is flat with the end of the plate tooth, stop the silk.
6) At this time, the spiny wheel handle is adjusted to reverse, and the dental mold head is slowly exit the pipeline.
Precautions
Before operating the setting machine, you first need to understand the operating procedures for the set of wires, so as to better use the tools and complete pipeline processing.The following editors will introduce the operating procedures for the use of the wire machine.
First of all, the silk machine should be placed on a steady basis, operates empty first, check and adjust, and operates normally in each component.The diameter of the processing pipe must be selected and installed in order. When the operation, you should first use the lubricant lubricant tooth.
During the work of the silk machine, when the length of the workpiece extended to the jacket is too long, the rear must have auxiliary support and adjust the height.Check whether the machine is running normally. If there is an abnormal sound, it should be stopped immediately to remove it. It can be continued to be used after the failure.
Check whether there are oils before operation, whether the oil pipe is smooth, and the application brush should be removed in the operation. Do not knock the vibration and clean it in time.At the same time, when entering the workpiece, it should be placed, flat, and stable to prevent the hands and clothes from being rotated and hanging.
When ending the filament machine operation, you must not add a long force on the rotating handle. When cutting the tube end, you must not enter the knife too fast.After the operation of the silk machine is completed, the power should be cut off, the power gate is locked, and daily maintenance should be done.
During the operation, you must pay attention to protecting the set of silk machines so that the service life can be extended. In addition, regular maintenance and maintenance work can make the silk machine more convenient and effective in operation.
Pay attention to the safety of the silk machine. The Emerson pipeline tool reminds everyone that the actions in any non -rotating state should be stopped.You can rotate the front and rear cards in the direction of clockwise, loosen the three claws, load the tube from the rear card, pass through the front card, and extend it about 10 cm long.
How to maintain the silk machine
The filament machine operator can grab the tube with his right hand, tighten the machin first, and then tighten the front card. Then, the hammer strike the disc according to the counterclockwise direction.Plate cuts the blade frame and the chamfering frame, let the open position, put down the plate head, make it contact the square block, lock it with locking. After the plate tooth head is reliable, press the button to start the device.
The maintenance of the silk machine is very important. It is recommended to clean the oil disc every day. If the oil color is black or dirty, the fuel tank should be cleaned and put on the new oil.In addition, after the work is over, clean the tooth and plate tooth head, check the teeth of the plate tooth, remove the dandruff between the teeth. If damage is found, it should be replaced in time. You should not only replace one when the plate tooth is replaced. One pair should be replaced.
In order to ensure the lubrication of the front and rear bearing, the two oil cups on the main axis case should be cheered at the time of use, which must not be less than twice a day.Check the cutting blade every week. When you find that you are blunt, replace it in time, and clean the fuel tank filter every week.It is necessary to check the wear of the equipment every month. If the wear is severe, it must be replaced.
When the filament machine is not used for a long time, the power plug should be unplugged, the front and rear guide columns, and other running surfaces are applied to the rust -proof oil, which is stored in the ventilated and dry place to keep it properly.Only by doing equipment maintenance work can we better use the silk machine.

Related tags： Machinery