The harvester is the machinery of integrated harvesting crops.Complete the harvesting, samily granules at one time, and concentrate the grains to the storage warehouse, and then send the grain to the transport vehicle through the conveyor belt. It can also be harvested manually.Grain harvested machinery to pick up and pickup.What kind of harvester? What brand of harvester is good?
Types of harvester
Side hanging harvester
Hang the hook ring on the aluminum alloy sleeve of the transmission shaft on the strap under the shoulder of the operator, hold the handle, and swing the hard shaft in the horizontal swing to complete the operation of grass and shrubs.
Carrier harvester
Generally, the structure is similar to the side hanging and irrigation machine. The difference is that the engine is on the back of the operator. The cutting part is transmitted by a soft shaft, and the cutting is generally between 1.5 and 2 meters.
Hand -type harvester
The weight of the walking wheel support is promoted by the person to promote the machine, and the engine -driven work component is cut into cutting and irrigation.
Suspension harvester
Hanging behind the tractor, the power output shaft drive working parts rotate, suitable for large -area cutting operations.
Circular cutting harvester
The horizontal cutting harvesters have better adaptability to the growth density, plant height, inversion, and yield of rice and wheat.However, the operation timing group is poorly flexible.
Vertical cutting harvester
Light and flexible, good control performance, suitable for harvest rice and wheat on small pieces.Most of the 7-9 kW of hand -supported tractors or about 15 kW of wheeled tractor.
Tie
It can be tied directly during the harvesting process. After drying in the paddy field, it is mostly used to return to the cadrants for mountains and hills.
Cutting machine
Cut down the wheat straw and spread it on the stubble, and become a bars that are overlapped by the tail, so that the grain that is dry can be harvested.
Direction -type grain connected machine
The structure is simpler, but the maneuverability is poor in operation.Before starting the job on each block, artificial or other types of machinery must be opened.
Self -walking grain collection machine
It can open the way by itself, have good mobile flexibility, convenient to change the operating plot, and high labor productivity, but the annual utilization rate of its engine is low.
Suspension and semi -suspension grain collector
It has the advantages of both traction and self -running, but the stability and operating performance of the machine are welcomed.The connection of the semi -mounted tractor is simpler than the suspension type, and it is strong to adapt to the terrain.
Full feed grain recovery machine
The universality of various crops is better, but the required power is greater.The half -fed grain recovery machine requires small power and can keep the stems relatively complete, but the adaptability of the crop growth is poor, and corn, beans and other crops cannot be harvested.
Harvest machine purchase
The power of rice combined harvesters is generally 9--107kW.Therefore, the size of the selected model should be compatible with the size of the fields and the status of concentrated films.If the fields are flat, the fields are large and the high differences are small, and a large model should be selected; if the fields are small and are scattered, a small harvester should be selected.If the small field blocks are used to use a large harvester, the efficiency of the harvester cannot be fully played; the small harvester is selected by the field blocks, and the productivity is low and cannot meet the requirements of the rapid harvesting of the agricultural busy season.
Harvest machine use
1. Before harvesting, check whether each component of this harvester is intact.
2. Drive the machine into the field, then pull the straw pole to the operating location, put down the grain platform, remove the grain to remove the gate to the "open" position, and hang the grain bag on the grain bag.Location.
3. Debug the machine: Send the dust adjustment handle to the "standard" position, and the secondary transmission handle according to the conditions of the crop, select the position of "high -speed" or "low speed", and the weaken handle is placed in "cut grass" or "drafts""Location.
4. Drop the cutting platform to reduce the front end of the granulatory device to the place 5-10cm on the surface of the field.
5. Wall out the clutch and cut the clutch handle to the combined position.
6. Slowly push the main speed handle forward, so that the machine begins to harvest.
7. When the crop starts to enter the drooping mouth, the depth of the operation of the decarning can be manually adjust the switch to make the ear head at the position where the depth of the depth indicator.
8. After all the crops are harvested, the clutch handle is pulled to the separated position
9. Wait until the grain port is no longer out of food, pull the foil clutch handle to the separation position.
10. Check whether the machine switch of the machine is closed well.
11. Reduce the throttle and the engine turning off.
12. Put the reaction machine and put it on and perform a certain inspection and maintenance.

Related tags： Machinery