HOME > NEWSarticle

What to do if theoilet waterank is noon wer 2024-07-21 17:11:11 internet

Although the slow water on the toilet water tank is not a big problem, it still has a certain impact on the quality of life. It feels worthless to find someone during maintenance, and it will affect the mood of entering the toilet.In fact, as long as you understand the principle of the toilet, you can find the solution ...
Toilet water tank is not water
1. The water pipe of the toilet is blocked; 2. The plug in the toilet water tank failed to block the outlet.
Toilet water tank repair
When the water tank is filled with water, the water inlet valve continues to enter the water: (1), check whether the pressure of the tap water is too low (below 0.05MPα) or too high (0.8MPα).(2) Check whether the floating body of the water inlet valve is freely up and down, and whether it is stuck by the water tank wall or other parts.(3) Open the water inlet valve and check whether the sealing ring in the valve body is stuck or shed and displaced by the debris.(4) Check whether the water inlet valve is broken.
Toilet water tank water level adjustment
First lift the horizontal center of the valve adjustment pole to lock the screws in the center of the ball, and the distance between the water level from the water level is 20-30mm.Look at the water level, let the screws extend for a while when it is low.Just adjust it like this.If it is a wire, move it with your hand, and the key to the water is still in the original position, and it will not last a few times in a row.
Toilet water tank leakage
The cause of the toilet leakage is generally on the drain valve. The toilet leak inspection site: whether the drain valve installation hole is deformed or the cracking drain valve installation surface is severely bumpy and uneven.Whether the biased drainage valve bottom hook screw is overlooking the ceramic hole bottom drainage valve seal film and the covers the sealing drain valve seal the film whether the film is deformed or loosened or the cover surface has impurities.
Toilet water tank structure diagram
The structure of the toilet water tank is shown below:
Toilet water tank installation
First of all, the toilet water tank is an important core of a toilet, and its structure is also a must -know information in the industry.Once we know the relevant structure of the water tank of the toilet, the toilet maintenance will be targeted in the future.Although the style of the water tank is different, it has the same structure and the same working principle.When installing the toilet water tank, we must follow the location of the eye of the rear wall of the water tank according to the height of the water tank.We must fix the corresponding position when we are drilling on the wall. After drilling the eyes, knock into the steel bolt, so that the water tank is in place.After the position of the rear wall eye, the expansion bolt is covered and the 3 mm thick nylon cushion is added to fixed and tightened.
Slow water in the toilet water tank
In the first trick, most of the problem of toilet water has a certain relationship with the faucet. The lack of water from the faucet of the toilet will naturally lead to the slow water. There is a filter in the toilet water supplementer.There are a lot of dirt on the Internet, so that the flow of water will be affected, and you can take it down to clean it yourself.The valve should be checked at the connection of the water tank, and re -spraying the water can quickly discharge the water in the water tank.
Toilet water tank overflow
Analysis and solution of the cause of the toilet water tank overflow (1) The pumping tank has been filled with water, but the water continues to end up until the overflow.Under such circumstances, we can try to do the test inspection first: drift the water to pull up the water to observe whether there is still water in. If not, it means that the location of the water drifting is not suitable.At this time, the water drift is low, so that the buoyancy can be increased to close the water inlet valve port.If there is still water in the water after bleaching, it is likely that there is a problem with the component of the automatic water inlet valve, and you must ask the aquatic master to check and repair.(2) The toilet water tank is overflowed from the side, just like putting the cup crooked, a thin current flows along the water tank.Toilet water injection is constantly overflowing water. Generally, it means that there is a problem with the water inlet valve. First of all, the quality of the water inlet valve is considered. It is not ruled out that it is caused by improper installation.If it is used well a few days ago, a spill will occur without the toilet, indicating that there is still a fault in the water inlet valve. At this time, you can replace a water inlet valve with the same specifications.If it is not installed properly, you can open the water inlet valve floating barrel to see if there is any impurities. If you have some, just adjust the orientation.

Related tags: news