At present, the water dispenser products on the market are mainly divided into two categories: barrel -mounted water dispenser and pipeline water dispensers. During the use of household drinking water, water dispensers often have faults such as leakage and indicator lights.Can be effectively dealt with its fault.
Raiders of the water dispenser
(1) Put it lightly when moving the water dispenser. The removal of the refrigerator water dispenser should be kept upright and moved. When it is to be tilted, it must not be greater than 45 degrees.Essence
(2) The newly purchased water dispenser is used to rinse the container and pipelines of the water dispenser, and then the drain valve is turned on, and the drainage valve is tightened after the remaining water in the discharge.After the barrel water is added, open the hot water faucet, and after the water flows out, the power supply can be inserted, the heating switch is turned on to avoid dry burning and extend the life of the machine.
(3) Drinking water for a long time, please turn off the machine switch and pull off the power plug, turn on the drainage valve, finish the water in the drainage, and then tighten the drain valve. Use a towel to dry the water tank water. Clean the surface of the case.The water dispenser is packed into the paper packaging box.
(4) Ensure that the use of water dispensers is safe. It is best to disconnect the power when it is not used at night.
(5) The use of the water dispenser should be cleaned and disinfected once every 3 months. For one year, it should be cleaned to the intelligent seat and the inner orchestra.
(6) The water dispenser should be placed in a ventilated place to prevent humidity, avoid direct sunlight, and stay away from the heating to avoid the fading of the case.The water dispenser must be stable. It is best to be about 15 cm away from the wall. Do not place it next to other household appliances to avoid splashing water or danger.
(7) Forbidden the surface of organic solvents such as gasoline.
(8) The proper use of the water dispenser should deal with the socket and leakage protector that performs the grounding device to prevent the shell from charging.
(9) Do not put the metal rod into the backboard to ventilate the fan to avoid damage to the fan or cause electric shock; do not cover the fan ventilation window, so as not to damage the semiconductor refrigeration component due to poor exhaust air and poor heat dissipation, and cause adverse situations.
(10) The water dispenser with a compressed machine refrigerates. When the cooling power supply is disconnected, it can be started again after 3-5 minutes to extend the life of the machine.
(11) When pushing the faucet, do not excessively force, so as not to turn or damage the part by hand.
Common causes of water dispensers exclusion
1. The heating light is not bright and not heated
Cause of failure: (1) Due to the dried water in the water dispenser during installation, the water is not powered off.
Processing method: disconnect the power and turn on the back panel. There are 2 thermostats on the side of the thermal gallbladder, one of which is the temperature control of the switch to prevent dry burning., Power -powered inspection, this is the heating indicator light, turn off the power, and twist the back.
Causes of failure: (2) The reset temperature controller is not reset.
Removal method: (1) Unplug the power plug and cut off the power;
(2) Waiting for the hot pot water temperature to be less than 25%, press the reset button of the temperature controller.
2. Water dispenser leaks water
Causes of faults (1) The floating valve of the water purifier is not installed properly. When the water drinking box is full of water, the floating valve fails to stop the water from the water under the water purifier and cause water leakage.
Removal method: Re -install the floating valve and first try whether it work normally under the tap water faucet and then place it on the water dispenser;
Causes of faults (2) The silicone tube in the water dispenser is loosened by transportation.
Removal method: Open the back board, observe or add water to observe which interface position leaks. After finding it, use the new tie or the original tie line to combine the silicone tube on the interface.After repairing, use a dry cloth to dry the parts in the water machine.
3. Water dispenser faucet seeping water
Causes of faults (1) Whether the tightness of the faucet is tightened;
(2): Whether the tap of the faucet rubs the teeth.
Removal method: Tighten the red or blue part of the faucet clockwise, so that the faucet is reset and fastened.Or unscrew the time clockwise, adjust the silicone tube and spring in the faucet with your hands, and then re -twist the faucet; you can also allow the after -sales service personnel to replace the faucets buckle or open the entire faucet for replacement.
4. Cold water dispensers, hot water skewers temperature
Causes of faults (1) The water level in the machine seat has been full of hot water outlets.
Exclusion method: Check whether the water purifiers floating valve is not installed.
Causes of faults (2) The water inside the stagnant water of the water dispenser has been filled and covered with the hot water breathable holes on the side of the water side of the water dispenser, or the hot and cold water is connected together to cause a string of warmth.
Solution: You can reinstall the floating valve.
Causes of faults (3) The unidirectional valve fault on the hot water bile connection tube in the machine seat, the hot water flow back to the water storage bile, and the hot and cold water is connected together to cause a string of temperature.
Solution: Replace the unidirectional valve.5. There is no electricity in the whole machine (without heating, not refrigerating)
Causes of failure
Water dispenser
(1) Check whether the power socket is electric, if there is no connection.
(2) Is the power plug and socket contact reliable?If loosening, it is firmly inserted.
(3) Check whether the connection of the inside and external power supply is disconnected?Does it fall off with the plug -in?If there is, connect well.
6, leakage
Causes of failure (1) Power cable damage, cracked dew metal wire
Removal method: repair or replace
Causes of faults (2) Poor water dispenser.
Removal method: The three -hole sockets and the leakage protector must be used to use a reliable grounding of the ground, and the leakage failure is eliminated in time.Specialized personnel or use the Zhaou table to check ground resistance.
7, hot water is not hot, cold water is not cold
Causes of failure: too much amount of hot and cold water for a short period of time; the power supply is not connected; the cooling water cooling time of cold water is not enough.
Removal method: Wait a while, you can take the water again, pay attention to the appropriate water amount of the water dispenser; check whether the heating switch is placed in the opening position, whether the power plug is inserted, and whether the power socket is electric;
8. No water
(1) Water faucet does not produce water
Causes of failure: large bottle no water; water inlet, watery pillar entering the water inlet and being blocked by the large bottle cap.
Removal method: Replace a bottle of new water; remove the waste paper, pay attention to the sealing paper on the bottle cap, and put it with a large bottle of water.
(2) The cold water faucet does not produce water
Reason: Ice blocking.
Removal method: You can turn off the refrigeration switch for four hours.
9. Excessive noise of electric tube
Cause of failure: After long -term use, the electric heating tube is slightly scald.
Removal method: Wash hot tanks with 2%consumption of citric acid.

Related tags： Appliances