Angle Grinder, also known as grinding machine or tray mill, is a grinding gear for glass reinforcement cutting and grinding.The corner grinding machine is a portable electric tool that uses glass fiber reinforcement and polishing, which is mainly used for cutting, grinding and brushing metal and stone.
Angle Grinder
First, prepare before using the corner grinding machine 1. The corner grinding machine must be responsible for it, and regularly check to ensure normal operation.
2. When replacing the new sand wheel, you should cut off the total power supply. At the same time, you should check whether the sand wheels should be crack before installation.Voice.(Metal sounds are excellent, dumb sounds).
3. The corner mill must have a firm and suitable sand wheel cover. The bracket must not exceed 5mm from the wheel, otherwise it must not be used.
4. When installing a sand wheel, the nut must not be too loose or too tight. Check whether the nut is loose before use.
5. After the sand wheel is installed, be sure to test for 2 to 3 minutes to see if its operation is balanced and the protective device is proper and reliable. When the test operation, one of them should be arranged.There are abnormalities, and another person cuts the power immediately at the power distribution cabinet.To prevent accidents.
6. Any user must wear a protective mirror, not to be opposite to the sand wheel, but should stand on the side.When using a corner grinding machine, wearing gloves should not be worn.
7. Check whether the sand wheels should be intact (no cracks, cracks or disability) before use, and whether the sand wheel shaft should be installed firm and reliable.Is there any debris between the corner grinding machine and the protective cover, whether it meets the safety requirements. When confirming that there is no problem, the corner grinding machine is turned on.
2. Precautions should be made during the process of using the corner grinding machine 1. When the sand wheel is motivated, it must be grinded after 40 to 60 seconds.Flying out of injury.
2. On the same sand wheel, the two are prohibited from using them at the same time, and they are not allowed to grind on the side of the wheel. When grinding, the operator should stand on the side of the corner grinding machine corner grinding machine.In order to prevent the crash of the sand wheel, accidents occur, at the same time, wearing glove operations are not allowed. It is strictly forbidden to launch and laugh and make trouble when grinding.
3. The standing position during grinding should be a clamp with the corner grinding machine, and the contact pressure should be uniform. It is strictly forbidden to hit the sand wheel to avoid cracking.(Aluminum, copper, etc.) and woody products.
4. When grinding the blade, the operator should stand on the side or oblique side of the wheel. Do not stand on the front of the sand wheel. At the same time, the tool should be slightly higher than the center of the wheel.Do not be too hard to prevent skids from being injured.
5. The sand wheel is not allowed to dip the water. It should be kept dry often to prevent balance after preventing wet water and accidents.
6. Do not abrasive objects on the corner grinding machine to prevent the wound from flying out of the wound.
7. Do not grind the workpiece with one hand to prevent falling off the sand wheel in the protective cover.
3. Precautions after use 1. Frequent trimming the grinding surface of the sand wheel must be trimmed. When the knife is found severely, it should be repaired with a diamond pen in time.
2. The sand wheel is thin and small, and when the wear is severe, it is not allowed to be used. It should be replaced in time to ensure safety.
3. After grinding, the power should be turned off. Do not let the corner grinding machine rotate. At the same time, it is necessary to remove the dust in the protective cover, and regularly repair and replace the main axis lubricating oil.
What needs to be specifically explained is that the corner grinding machine is used to polish, and the saw cutting function is not the original intention of the designer.Due to the high speed of the corner grinding machine, it cannot be pressed forcefully when using a saw piece or cut piece, and it cannot cut more than 20mm thick hard materials. Otherwise, once it is stuck, it will cause saw blades, cut slices, splashingIf it is light, it will damage the items, and it will hurt people! Please choose a high -quality saw blade above 40 teeth, keep your hands operation, and take protection measures.
The purpose of the corner grinding machine
There are many corner grinders, and woodworking, tile workers, and electric welders are commonly used.Installing the woodworking saw blade is a dexterous lacked woodworking chainsaw. Simple carpenter work can cope with it. Many masters who install flooring use it.Installing the sand wheel is a small hand -to -tech wheel cutter, which can cut and polish small metal components. Metal processing, such as stainless steel anti -theft windows and light boxes, can be made.The most important corner grinding machines for stone processing and installation can be installed with a series of clouds cut slices, polishing slices, wool wheels, etc., cutting, polishing, and polishing all rely on it.

Related tags： Appliances