The gas stove is a kind of stove. It mainly supplements the lack of air during burning by supplying natural air by supplying natural air between the gap between the stove and the upper cover, thereby promoting the combustion and reducing the production of carbon monoxide and nitrogen oxides.The gas stove in wind is divided into upper wind, downwind, and full wind, etc., and can be divided into multiple categories according to different classification standards.According to the source of gas, the gas stove is mainly divided into liquefied gas stoves, gas stoves, and natural gas stoves.According to the stoves eyes, it is divided into single stoves, double stoves and multi -eye stoves.
What are the categories of gas stoves?
1. Divided into use gas species: sky gas stove, artificial gas stove, liquefied petroleum gas stove electromagnetic stove
2. Divided by the material: cast iron stove, stainless steel stove, enamel stove
3. Press the stove eye: monocular stove, double eye stove, multi -eye stove;
4. Press the ignition method to be divided into: electric pulse ignition stove, piezoelectric ceramic ignition stove
5. Press the flameout method to be divided into: manual flameout cooker, timing off the stove
6. Divided into: desktop stove, embedded stove
Wheels of embedded stoves
There are three ways: downward wind, upper wind and full -length wind.
1. The next wind, as the name suggests, enters the fresh air under the cooker to provide the oxygen required for sufficient combustion. The advantage is that the fire is large, the thermal load is high, and it is in line with the hot and frying cooking habits of Chinese families.However, the installation of an embedded downwind cooker must pay attention to adding a second air channel in the cabinet below. Otherwise, insufficient air will cause insufficient gas combustion, produce high concentration of carbon monoxide, and even cause serious consequences such as ignition and explosion.
2. The stove that is in the air does not need to open the hole on the cabinet. It uses a higher stove head to enter the air from the furnace head.However, this kind of cooker does not have a good effect in actual use, mainly because the thermal efficiency is low, and it cannot provide high temperature.
3. Full -air stoves combine the above two ways of inlet air. The effect is relatively best.
How to maintain the gas stove
① Because the electronic ignition is a ignition of the circuit consisting of piezoelectric ceramics and metal, the food that is usually burned should not be dripped and the electrode is kept clean.
② Clean up in time for blocking the burner.
③ When the ignition difficulties occur, check whether the electrode is too large to the stove, whether the ignition hole is unblocked, and whether the piezoelectric ceramics fails (fire weak) the metal component is shedding.Otherwise, you should go to the office to report it in time.
Maintenance and maintenance of gas stove:
1. Frequent cleaning and removing the stains on the gas stove to prevent rust from rust.
2. The burning device is easily stuffed by the dust of the rice.
3. The inlet of the burner may sometimes be stuffed by various debris.
General repair of gas stove:
1. Four switch binocular iron plate stoves
The four -clock -shaped iron plate stove is the opposite of the direction of the handicap of the two -switching iron plate stove, that is, when the hand is parallel to the stove, in order to close it, the vertical stove surface is all open.
2. How to take the "Burn"
First turn the pot, then lift the burner slightly to remove it.
3. How to deal with "switch tight"
You can remove the stove panel, and use the panel or a small hammer to clock the switch at the top of the switch gently, and add a little lubrication to loosen.
4. How to deal with "small fire"
You can remove the burner, then ignite it on the spraying, burn red with thin iron wire, dredge it inward, and wait for the sprayed firepower to sound.
5. Daily maintenance and precautions for electronic fire stoves
① Because the electronic ignition is a ignition of the circuit consisting of piezoelectric ceramics and metal, the food that is usually burned should not be dripped and the electrode is kept clean.
② Clean up in time for blocking the burner.
③ When the ignition difficulties occur, check whether the electrode is too large to the stove, whether the ignition hole is unblocked, and whether the piezoelectric ceramics fails (fire weak) the metal component is shedding.Otherwise, you should go to the office to report it in time.
Maintenance method
There are two most common faults in electronic gas stove maintenance.
1. The ignition machine does not produce a spark of natural igniters piezoelectric ceramics.This failure is mainly to disconnect by the wire of the automatic switch to the CPPC.In addition, if the voltage (metal round stick) is stained or rusted to cause poor contact, it will also cause difficulty in ignition. At this time, you can pull out the metal round stick and use fine sandpaper to remove the dirt before inserting.
2. There is a spark but cannot ignite. Sometimes the distance between the positive electrode of the voltage ceramics and the negative pole of the stove is too far or too close, so that the spark can not cause the gas gas, and the distance should be adjusted to about 4 mm.In addition, the gas nozzle on the side of the near -point fireware is blocked by the benefit or other foreign objects, which will also cause difficulty or ignition difficulties. At this time, as long as the block in the nozzle is cleared.

Related tags： Appliances