The premise of healthy drinking water is to realize the correct installation of the water purifier, master the three mainstream water purification equipment: the installation steps and installation precautions of cabinet water purifiers, wall -mounted water purifiers, and water purifiers to make us drinkWater quality is effectively guaranteed.
Pay attention to the connection installation of multi -road valve products
1. Outside the outer teeth should be entangled with an appropriate amount of surrounding bands (also known as water tape) to avoid leakage or cracked.
2. When installing the O -shaped sealing ring, check whether the sealing ring is damaged, distorted, etc.
3. When the outer teeth are tightened, the force must not be too strong, otherwise it may cause threading to smooth teeth.
Precautions for the installation of water purifier
1. Water purifier installation staff should ensure whether the water quality, water inlet pressure, water flow, and water temperature of the water purifier should meet the requirements in the product performance parameter table.According to the quality of the water inlet, select the front filtering device in front of the water purifier.If the water purification pressure is less than 1 kg, you need to install a booster pump in front of the water purifier. If the water pressure is greater than 3 kg, you need to install the pressure decompression valve in front of the water purifier.In front of the temperature device, the installation position of the water purifier should be ensured below the position of the water boiling heater to prevent the steam in the boiling water heater from entering the water purifier and damaging the water purifier filter element.
2. All pipelines, joints, and faucets such as water purifiers shall meet national health standards.
3. Do not install it outdoors in the northern region to prevent frozen cracking superfilled elements and prevent direct sunlight.
4. When tightening the threaded joints during installation, you must not be too large to prevent the joint thread from slipping your teeth.
The installation method of pure water machine
1. Turn off the water, open the faucet, and let the remaining water in the tube.
2. Remove the faucet into the water pipe, install the water into the three links and tighten it with a wrench (when installing the water in the water, if there is a rubber pad on the joint, there is no need to wrap the raw material.)At the side hole of the water inlet, the water pipe of the water pipe is installed on the water inlet, and it is tightened with a wrench.
3. Turn off the water inlet valve, open the water source, and wipe it with a paper towel to check whether the installation joint seeps.
4. Three filter elements of PP cotton, particle activated carbon, and compressed activated carbon are loaded into the filter bottle in order, and tighten the filter bottle covers at all levels.5. In the pressure barrel exit, it is wrapped in an appropriate amount of raw material, install the pressure barrel ball valve, and use the PE pipeline to connect the rear activated carbon into the water outlet with the pressure barrel out of the water ball valve.
6. Water inlet pipe connection: When the kitchen type water machine machine is installed, the pipeline connected to the water inlet valve is directly connected to the machine first -level filter barrel water inlet interface; when the cabinet machine is installed, first open the lower part of the cabinet to the lower part of the cabinetThe pipeline and the pipeline and wire import and exit, lead the power cord out of the pipe and connect the water ball valve through the hole, lead to the cabinet and connect to the first -level filter inlet of the machine, and then check whether the connector is seepage of the water seepage.Essence
7. Rinse the front filter element: First remove the reverse osmosis membrane shell into the short PT tube, insert it into a container, open the water and power supply, rinse the first three filter elements, and go directly to the clear water.
8. Install the goose -necked faucet: Use steel nails on a stainless steel groove to beat a small groove (easy to drill), and use a flash diamond (M12 drill) to punch aversion on the groove surface.Then fix the faucet of the goose neck, the lower end of the goose neck faucet is connected to the 14PE tube, and the other end is connected to the exit of the active carbon filter element.
Cabinet water purifier installation steps
Step 1: Turn off the total water switch of the tap water, install the three links of stainless steel and the ball valve in the water take, and connect to the water inlet of the water purifier with the PE tube.Use a PE tube to connect to the mouth with a PE tube of about 15 cm, connect the plastic rinse of the ball valve, and then connect the PE tube with the right length.
Step 2: Open the fifth -level ultrafiltration device, remove the seal ultrafiltration element in the accessory to install it to the ultrafiltration device and tighten it with a plastic tight wrench.
Step 3: Check and turn off the refrigeration hot switch, insert the power supply and start rinse, and turn off the ball valve without dark water.
Step 4: Open the seabed sewage port (soft plug+nut) of the hot and cold bucket, and rinse for 25-30 minutes in turn until there is no white foam in the water.
Step 5: Wire the sewage nut, turn on the hot and cold water faucet, and let the appropriate amount of water.(Note: There are water flowing out of the hot water mouth to open the heating switch to prevent dry burning)
The installation step of wall -mounted water purifier
Step 1: Turn off the total water switch of the tap water, install the three links of stainless steel and the ball valve in the water take, and connect to the water inlet of the water purifier with the PE tube.
Step 2: Use a PE tube of about 15 cm to connect to the mouth, connect to the plastic rinse of the ball valve, and then connect the PE tube with the right length.
Step 3: Install the goose neck faucet and connect to the water outlet.
Step 4: Open the tap water switch and water inlet ball valve, and rinse the plastic rinse of the ball valve and wash the ball valve for about 5 minutes. After the rinse port, the plastic flushing valve is turned off without dark water.
Step 5: Open the goose neck faucet and rinse for 15-30 minutes to rinse the alcohol protection solution in the filter element (rinse until the water without alcohol) to use it normally.

Related tags： Appliances