HOME > NEWS > Appliancesarticle

Gas stove repair 2024-07-20 05:34:59 internet

Some faults that often occur during the process of gas stove include failure such as air leakage, abnormal flames, noise off -flames, no fire stoves, and automatic flameout of gas stoves.To prevent the occurrence of gas stove failure, the daily maintenance and maintenance of the gas stove is essential.
Reasons and solutions for automatic flameout of gas stove
1. The oil stain generated by the gas stove after using it not only affects hygiene, but it is easy to cause the gas stove to be blocked. Therefore, it is necessary to clean the gas stove regularly.
2. Find a professional to repair the fastel and gas supply system with a foaming agent on a regular basis.
3. Clean the stove tile.Use the abandoned candle head, the surface of the candle is smooth, even if there is oil stained on it, as long as the ordinary detergent is wiped gently with water, gently apply the seams of each tile, first follow the seams of the joints.Apply the direction, and then come over and apply it again. Be sure to make the thickness of the candle flat with the thickness of the tile.
4. Deep cleansing method of the stove.
Mix with two spoons of white vinegar with 200 ml of warm water, and then use sponge and environmentally friendly loofah to dip this hot vinegar water to clean the stainless steel stove to make it bright.
Use 500 ml of hot water to mix with 30 grams of baking soda (sodium bicarbonate). It can also be dipped in the stove to remove the stove.
Press 50 grams of soda directly into thinning, sprinkle it on the stove, and wipe it with a cloth.You can also use coarse salt to clean it. Use a rag dipped in coarse salt for pickled vegetables. You can easily rub the oil dirt on the stainless steel stove and the glass stove. Remember to wipe the salt clean, otherwiseDark.
Use the inside epidermis of the potato skin to wipe the stove on the stove where the oil is contaminated and the vegetable soup is discolored, and then clean it with hot water. You will see a particularly beautiful stove.In addition, use radish head and tail, cucumber and fragmented section to dip a little detergent to rub the oil stains of the stove, and then wash it with a rag dipped in water twice. The effect is also very good.
5. Clean the gas stove fire rack and air pores.First full a pot of water, put all the fire racks on the stove to cook. After the water is hot, the sticky dirt will decompose and peel off.Prevent the stoves pores from being blocked and remove the stove head every week, and clean up the pores with a toothpick.The carbides and scorchs accumulated on the stove can be removed with small fine brushes, or the fire holes can be pierced with fine iron wire.
The working principle of fire offering protection
1. The battery is out of power or poor contact: You can reload the battery again to ensure that each contact surface of the battery is clean, and then ignite it to see the situation again.If you still turn off the fire, you can change the battery at this time, and try again.
2. The problem of thermal probe: Watch the stove eye on the other side, can the flame in the middle be burned to the probe, and it must be burned to the probe to set the fire.At a time, you can hold down the species for ten seconds. When the switch is loosened, that probe is thermal sensing, you need to burn it to set the fire.
3. After the fire is hit, do not let go of the valve of the magnetic valve through the small mechanism on the switch. When the electric puppet reaches a certain temperature, let go, usually more than 30 seconds to one minute.
4. Maybe the electric puppet can not eat the flame. You need to adjust the wind door under the gas stove to make the fire a bigger so that the electric puppet can eat the flame to receive the heat and then transmit the heat.要 掰, pay attention to uniformly, do not break the electric puppet, and pay attention to cleaning up more electric puppets so that he can better transmit calories.
5. The feedback circuit of the gas stove is not smooth.To ensure the continuity of the burning, it is necessary to ensure the smooth flow of the feedback circuit. The feedback parts of the gas stove are mostly set in the place where the flame can be burned directly. When the flame is normal, the feedback circuit will provide the pulse with a continuous signal of gas supply. Otherwise, the pulse will beTurn off the solenoid valve.

Related tags: Appliances