Dongyuan inverter is a inverter produced by Taian Technology. Taian Technology is a private company of Ansai International Investment (Singapore), a well -known multinational company in Taiwan.Management and operation innovation, cultivate international talents and management talents, strengthen cooperation and exchanges between mainland and international, do the social responsibility of enterprises, produce world -class switches, circuit breakers, automatic control and industrial electronics products to ensure the globalSexual and comprehensive competitiveness is the goal of development.
Dongyuan inverter price
1. Settlement Inverter Tongyuan Inverter Brand/Model: SAJ/Trio Crystal/V1R5M3 Application range: Fan Special Brand: SAJ/Crystal Product Series: SAJ8000G model: V1R5M3.Quotation: 500.00 yuan 2. Dongyuan inverter brand/model: Taian/Taian/A.Quotation: 2300.00 yuan 3. Taiwan Dongyuan inverter, Wuxi Dongyuan inverter. Dongyuan inverter 7200mA series brand/model: Teco/Dongyuan/7200MA/380V1.5kW application range: Universal brand: Teco.Quotation: 1100.00 yuan
Dongyuan inverter wiring diagram
Dongyuan inverter wiring is as follows: (R, S, T) is transmitted by the power supply, and the inverter output terminal (U, V, W) receives the motor respectively.If you need to rotate the motor in general, you can use a intermediate relay to put these two points and the controlling contacts into the public terminal and the positive rotation start.Out of power, the motor stopped.
Tongyuan inverter after -sales service
Taiwans Dongyuan Products National Lianbao, product quality warranty for 12 months, 24 -hour response service.Among them, Dongyuan Electric Global Insurance, Dongguan Fuchuang Energy provides you with Taiwan Teco Dongyuan Electric 1/4HP ~ 60000hp (0.18kW ~ 45000KW) low -medium high -voltage motor and 13800V ultra -high voltage standards and non -standard motor motors.
Dongyuan inverter parameter
Dongyuan inverter failure code
1.OC. Over -current, this may be the most common failure in the inverter.We must first rule out the failure caused by parameter problems.For example, the current limit, the speed of acceleration is too short, which may lead to overcurrent generation.Then we must determine whether there is a problem with the current detection circuit.2.OV. Overvoltage, we must first rule out the failure caused by parameter problems.For example, the deceleration time is too short, and the overvoltage caused by the regeneration load, then we can see if there is a problem with the input side voltage. Finally, we can see if the voltage detection circuit has failed.Points are the voltage of the intermediate DC circuit.3. UV. Implit voltage.We can first see if there is a problem with the input side voltage, and then look at the voltage detection circuit. The fault judgment is the same as the overvoltage.
Dongyuan inverter instructions
Work temperature: Inside the Dongyuan inverter is a high -power electronic component, which is easily affected by the work temperature. The product requirement is generally 0 to 55 ° C. However, in order to ensure the safety and reliability of the work, there should be room for room.Control at less than 40 ° C.In the control box, the inverter should generally be installed in the upper part of the box, and strictly abide by the installation requirements in the product manual. It is absolutely not allowed to be installed at the bottom of the bottom of the inverter at the bottom of the inverter.Grounding problem: Dongyuan inverter correctly ground is an important means to improve the sensitivity of the control system and inhibit the ability of noise. The smaller the ground resistance of the inverter ground terminal E (G), the better the grounding area of ??the grounding wire should be not less than 2mm2.Within 20m.The grounding of the Dongyuan inverter must be separated from the places of the power equipment and cannot be together.The shielding layer of the signal input cable should be connected to the E (g), and the other end must not be connected to the ground end, otherwise the signal changes fluctuate, causing the system to oscillate.The inverter and the control cabinet should be connected by electrical. If it is difficult to install, the copper core wire can be used to cross.

Related tags： Appliances