For the caregivers of mountain cars, mountain cars have been taken care of.On the way out to travel, mountain cars will inevitably fail, and various changes will occur in the motor structure of the car, so learning is correct ...
How to maintain mountain cars
For the caregivers of mountain cars, mountain cars have been taken care of.On the way out of travel, mountain cars will inevitably fail, and various changes will occur in the sports structure of the car. Therefore, it is necessary to learn to use, maintain, and repair bicycles correctly.How to maintain the mountain car?
1. Clean and maintenance of the frame
Cleaning the frame can be poured into the part with a rag dipped in water, so that the mud sticking under the frame is very soft after encountering water. At this time, you can easily remove the mud.It is disliked to use high -pressure water guns to rinse the sludge on the bicycle. Because of this cleaning, the water is easy to enter the central axis or flower drums, affecting the life of the parts.At this time, you need to pay attention to some places that are easy to accumulate on the frame, such as the position of the five -way in the middle shaft.After washing the mud on the frame with water, pour a little detergent on the rag. After simply rub it with your hands, you can scrub the frame on the frame.Wipe it back and forth a few times, and the frame will clean up.Usually it is not recommended to use powerful pollutants such as washing powder, because many bicycles are aluminum materials, and the alkali ingredients contained in washing powder will have a chemical reaction with aluminum.Patterns, so flexible pollutants -detergent is by a better choice.
2. Round group, front and sitting tube
When washing the wheels, you can choose to dip the shoe brush to dip the sediment on the tire on the outer tire.In the car washing circle, it is best to replace it with a rag with detergent, and carefully wipe the cars brake skin brakes.Simple scrubbing in spokes.When finishing the flower drum, do not remove the detergent with high pressure water guns.Just simply pour the water and wipe it with a clean rag.When washing the pipe and sitting bag, be careful not to let the mud water flow into the sitting tube along the seam of the sitting pipe clip.Under a bag, it is often the place where the mud is the most up to the most, and you must carefully wipe the mud with a rag.For tires, you can use a slightly harder brush to brush the gravel and dust on the tire for simple maintenance.
3. Finger, dial, dial, back all time
After washing the above accessories, the next time was washing fingers. The finger was more complicated in the dial. There were more butter in the parts play a lubrication effect.It is best to gently wipe it with a rag when cleaning fingers, just clean it.When the front and back are dial, you can use the water pipe to directly rinse the gap in the gap between the front and rear, so that you can rinse the stuck in the mud water and sand in the front and rear dials.After rushing off, you can also use detergent to wash off the oil on the front and rear.
4. Forks, pedals, brakes
Cleaning the fork and pedal is very simple, just wash the mud water from the pedal.It is best to rinse in the front fork without water. When rubbing the inner tube of the fork, the water on the rag should be wired and then wiped the inner tube of the front fork.After a period of use of the inner fork for a period of time, some impurities will be left on it. You can use a cotton swab gently. It is best to develop the habit of keeping the front fork cleaning. This is also the most basic maintenance of the front fork.When washing the brakes (prevails with V brakes), you can use the water pipe to directly wash the sediment left in the brakes to prepare for the next maintenance.For wheels, front and rear transmissions, guide wheels, etc., you can use a brush to remove dust and small dirt.
5. Dental, flywheel and chain
Throughout the process of cleaning, these three accessories may be the dirtiest part.Because there are lubricating oil on the accessories, dust is the easiest to adhere.We can also pour the detergent on the rag first. After dipping the water, we can clean the tooth tray. When washing the tooth washing, try to wash each tooth with a rag. After the washingWill be surprised to find that under the scrub of the detergent rag, the tooth plate is as bright as new.The next thing to wash is the flywheel.Washing wheels should be removed and cleaned.First relax the brakes, so that the brake will not be sandwiched.Turn the screws on both sides of the rear wheels. At this time, shoot the rear wheels gently, and the wheels can come out.Put the wheels on the ground, wipe it with a rag on the flywheel, put the wheels on the car, pay attention to the position of the back, and slowly pull it to put the wheels in.This process is very simple, you can understand after one or two disassembly.
Finally, the method of chain cleaning: The first is to use kerosene to wash chain to drag the chain with a rag with kerosene to drag back and forth.The disadvantage is that it will leave the odor on your body, and stick to the stains and oil stains.The second method is to use detergent.It should be noted that when washing the chain, it is best to use hot water of about 45 degrees. This temperature is easier to play its cleaning effect.In addition to wiping the chain with sticky cloth with a sloppy cloth, it is best to slowly brush each chain with a thicker brush, and the black chain will show the original color.
The above editor introduces the maintenance skills of mountain cars. The maintenance of mountain cars is divided into five parts. I hope it will be helpful to you!

Related tags： Auto Accessories