Wireless glue machines can be used to bind books, albums, signatures, hardcover books and other books. It is especially suitable for the use of graphic production centers, libraries, studios, small and medium -sized printing companies and other places.Improper use of wireless glue machines, it is inevitable that there will be failure behind the core milling, incomplete glue on the back of the book, poor gum on the side glue, etc. Therefore, you must pay attention to maintenance and timely solve the problem.Lets take a look with Xiaobian.
Booking machine maintenance method
How to maintain different types of binding machines
1. Financial binding machine
1. In order to ensure the normal operation of the binding machine, reduce wear, protect the accuracy, and extend the service life, it must be reasonably used and systematically lubricate, maintain and maintain the machine.All the transmission parts add lubricating oil once a week, and carefully wipe the overflowing oil to avoid polluting paper when cutting.Each months certificate binding machine is turned on and refueling below. All the transmission parts must be lubricated, but you must carefully ensure that the oil cannot be injected or wiring on the electrical equipment land.2. The binding machine must first cut off the power supply when repairing, adjusting, refueling, 揩 2 2, and inspection to avoid danger.
3. Do not put any irrelevant items such as oil pots, tools, etc. on the workbench at work.
4. If an accident occurs after booting, when there is an abnormal sound or stuck, the cause must be stopped immediately.
5. During the operation of the machine, it is strictly forbidden to put the hand into the rear of the knife. Even if the hand is stopped, it is strictly forbidden to make the hand under the knife to adjust the knife.
Second, hot -melt binding machine
1. Avoid placing the whole machine in direct sunlight and strong light.Do not exceed the capacity of the hot glue cover.
2. Other foreign bodies are prohibited in the heating tank.
3. Select a beautiful and firm hot -melt sealing sleeve. Do not use the sealing of the spine to make a seal set for plastic materials for binding.
4. Foreign objects are prohibited from entering the binding tank. When an accidental foreign body falls in, the power must be turned off before removing.
5. The heating board is forbidden to heat it to other objects.
6. Keep the binding slot clean to prevent any liquid from splashing.
7. Do not use your hand to step up to step up the push board. After non -continuous binding is used, please turn off the power.
Third, combing binding machine
1. Do not insert the metal into the mouth of the paper.
2. Keep the binding machine stable when the binding machine.
3. When the binding machine is not used, it should be placed horizontally. Do not reverse it.
4. We must clean the paper chip box frequently to keep the binding machine clean and dry to avoid moisture.
5. Do not pull the rubber ring too long or too frequently.
6. Select the specifications of rubber ring that meets the requirements to avoid affecting the quality of the binding.
4. Ordinary electric binding machine
1. After using it for a period of time, open the cover to clear the paper crumbs inside.Add a little lubricating oil to the shaft and activity to maintain the performance of the machine.
2. If the power decreases after long -term use of the motor, you can remove the motor. Two adjustment screws at the end of the motor. Take out the carbon brush inside and extend the spring.Just swipe and change it.
3. After the belt is broken, you must buy the same specifications of the same specifications from the local rubber product store in time.
Failure of the binding machine
1. The motor turns slowly or does not turn slowly or does not turn.
Reason for failure: One of the phases is disconnected from the machine.
Elimination method: Fix one of the power supply to find the card and eliminate it.
2. The binding machine does not rotate by power
Causes of failure: The circuit has no voltage, and the switch is in poor contact.
Elimination method: repair the power repair switch.
3. Stopping the normal work of the binding machine
Causes of faults: disconnected on the circuit, the power supply is interrupted.
Method: Repair the road and repair the power supply.
4. The binding machine belt electricity
Cause of failure: Motor insulation breakdown two -phase lead.
Elimination method: Repair motor winding check to eliminate the leading line.
5. Swing up when the knife is rotated
Cause of failure: This occurs because of the deformation of the drill knife, and it may not be installed.
Method: Replace the drill knife in time, or install the drill knife.
6. Pressing rivet
Cause of failure: The temperature of the binding tube is not in line with the temperature of the machine.
Elimination method: The suitable binding tube should be replaced. If the temperature of the hot rivet is too low, the hot rivet should be repaired in time.
Hot melting reservation booking process and precautions
What are the hottest installation and booking binding process?
1. Connect the external power of the hot -melt installation machine, and then turn on the power switch on the right side of the hot -melt installation machine and insert the file.
2. At this time, the hot -melt -setting machine heating tank is opened. The machine begins to preheat, and the preheating time is one minute.
3. Sort it up and put the text that need to be binding into the hot -melt seal, and align up, down, left and right, especially at the sealing ridge.Please select the appropriate gear according to the file size, which can effectively improve work efficiency.
4. Put the organized files in the machine heating tank to determine the flat contact with the machine heating plate.
5. After all the green work indicators are on and vibrate, the clamping board will automatically open, and then the binding text is taken out.
6. The binding text should be placed in the electronic air -cooled place. After the text is completely cooled, it should be turned over.
7. The binding is completed, the return is cleaned, and the power is turned off. After the machine is completely cooled, the collection is properly collected.
What should I pay attention to when operating the hot melting installation machine
1. When working on a hot -melt binding machine, do not touch the heat sinking hole outside the heat of the heat of the cooling window to avoid scalding your hands. At the same time, do not cover any objects on it.
2. The hot -melt binding machine is only suitable for indoor use. Properly extend the heating time, and the effect is better after the binding.
3. During the work of the machine.Do not touch the machine with your hand to heat the slot, and be careful.
4. After the hot rivet, do not touch the rivet head when taking out the file, because the temperature will be higher after the heat.
5. Do not roll the text immediately after heating, it is easy to cause the loose pages. After the glue is completely cooled and solidified, it can be turned over.
6. When using the hot -melt installation machine binding, it is necessary to arrange the files neatly before putting it in the seal, otherwise the binding files will be uneven.