However, most of the DVDs have now been used, but there are still people using VCD. How to make a VCD video disc?Still, it is very simple.Prepare the recorded blank disc, the burner (can be used, no expensive or low), and VCD burning software.Lets take a look with Xiaobian below!
How to record VCD discs
Facing the increasing amount of data at present, as the price of the CD-ROM and the CD-R fall, many people have purchased the recorder, used it to record, save data, and greatly facilitate the storage of data.There are also many burn software, such as WinonCD, Direct CD ...However, the CD -ROM is not a simple matter, which will be engraved with the disk, which will be available in each of each of the records of the disc.Now use the Acer BenQ recorder, the burning software is the Chinese version of WinonCD 3.6 Power Edition. During the use process, the lesson is summarized and published, so that everyone can master the techniques of as much as possible and reduce the use of CD-Rs unnecessary sacrifice.
1. Turn off energy management
Generally, the time to record the CD has a long time. If the energy management is set, it may cause the computing to stop the response for a long time, resulting in the failure of the engraving disk.Therefore, we must first close the energy management. Turn off energy management from two aspects: First, set Power Saving in Power Management in CMOS to None;The contents of "System Waiting State", "Closing the Monitor" and "Turn off the hard disk" are selected from the drop -down list "never", and click the "OK" button to return.And save it into a "CD -ROM" scheme.
2. Do not execute other Windows software when engraving
Try not to install too much software to install the computer, otherwise it may cause software conflict, causing the failure of the burner, let alone execute other Windows software at the time of engraving.
3. Use a low -power record CD
At present, the general recorder basically supports a speed of writing a CD of more than 4 times, but the author still strongly recommends that you use 2x speed engraving, because the use of 2 times or 4 times the speed of the disk can greatly reduce the occurrence of the interrupt phenomenon of the engraving process.The method is: in the "CD" window of WinonCD, click the "Output" tag item, select "2X or 4X" in the "speed" drop -down list, and then click the "British" button.
4. Test first and then write
Although most of the recording machines now support direct writing functions, it is best to test it before formal writing. If the speed test is not up (Speed ??TestFails) or the operation timeout (BUFFER UNDERRUNS) error, you should organize the hard disk againAnd reduce the speed of the burner until successful.The specific method is: In the "CD" window of WinonCD, click "Write to Test" in the "Write Test" tag item, "Write once and test, and then write it".
5. Try to use the same burning software
Because there are many recordings in the market now, their burn principle is not necessarily the same.I suggest you choose your favorite burn software and then use it to record the disc.For example, the authors machine uses WinonCD 3.6 Power Edition Chinese version.
6. Dont record continuously
Because the laser head used in the recorder is written, when it is a CD-ROM, a certain power must be achieved to melt the material on the CD-RW or CD-R material for burning.If the use time is used for a long time, the temperature on the recorded light drive is very high, and it may cause the burning error or even damage the optical drive.I suggest that you do not record multiple discs in a row, even more in the hot summer!
How to optimize the quality
The quality of the burns is related to the stability of the recorder, the quality of the burners CD, and the operation of the burning.First of all, the working status of the recorder must be stable, which means that the recorder can be used normally.The second is that the quality of the CD used to record is better. If the disc appears before it is recorded, this will not be able to talk about the quality.The operation of the burns mainly refers to the speed of the burner. Generally, the slower the better (2 times the speed of the speed), so the 2-4 times speed is a better choice.Most of the new types of recording machines now have the function of burning and immortality, but the use of burning and immortality can make the recording gap. Although this gap is very small, it will not affect the use, but the quality of the burning is damaged (the audio discs are damaged (for the audio discmost influential).Therefore, try not to use the function of burning and immortality is one of the ways to improve the quality of the burning.
In the process of use, the recorder should pay attention to the working temperature as much as possible. Excessive working temperature will cause the burns to decline or even fail.
The cleanliness of the burning disc will also affect the quality of the burns. If there is a dust existence on the surface of the CD disc, this will inevitably affect the strength of the laser to the disc, and the quality will be reduced. Therefore, we must pay attention toClean.
Precautions when using the recorder
When using the burner, we should pay attention to the following: (For the recorder with a burning function, the following 1-3 points can be completely ignored)
1. Prevent caching in arrears
"Buffer Under Run is a typical cause of the failure of the engraving disk. We know that the recording machine has a cache that is used as a temporary storage area to write the data into the CD. If some reason, the data flow isThe speed of entering the cache is lower than the speed of leaving the cache, which will cause the recorder to run in the arrears.It may ensure that the data flow is transmitted steadily and rapidly and is not interrupted.
Second, organize hard disks
The hard disk finishing here refers to disk scanning and fragments of each logic partition of the hard disk before the burning.In most cases, we use the hard disk as a source disk to record or make the CD to be replicated into an image and store it on the hard disk.The recorded data is distributed continuously on the CD -R disc.The sector must not only be connected from the beginning to the end, but also the IS0 9660 format also requires that the file must be a non -intermittent single -content sector sequence on the CD -R disc.However, because the unprecedented disk files are mostly scattered.In this way, when the hard disk reads data, no matter how fast the speed is, the reading and writing head have to be "exhausted" between scattered files, which is likely to cause unnecessary delays and cause the waste disk.So, do hard
Disk finishing is the first step of successful burning.
3. Avoid performing any unrelated procedures during the burning process
These programs include not only screen protection procedures and memory resident procedures (such as certain anti -virus programs and instant translation programs), but also other background running programs and games.These programs are likely to transfer the critical juncture of the data flow from the hard disk to the CD -ROM to compete for limited system resources with the burning software, which affects the normal transmission of the data flow and causes problems such as cache load.
Fourth, select the burning software
“有了稳定的系统，还必须配合好的光盘刻录软件，才能有效地提高刻录的成功率。找出最适合你在使用的刻录机的刻录软件来使用，但要注意选用较新版本，因为The new version means better support for the correction and hardware.
Fifth, use quality reliable plates
At present, the range of blank plates on the market is large.According to the different reflective layer materials, the four categories: Platinum, golden plate, blue plate, and diamond disk; these four plates do not have a significant difference in advantages and disadvantages, they can be purchased with confidence.In terms of characteristics, the Platinum plate has good compatibility. It is applicable to low -speed to high -speed recorders, and the price is very cheap; the blue plate has high accuracy when writing and reading data;Anti -light.Diamond discs have the highest recognition disk and read speed, but high -speed burns can be used well.The key is to try different categories and brands of discs, and find out the plate that is best for you to record machines.
6. Pay attention to heat dissipation
Poor heat dissipation is also an important reason for the bad disk.Especially in the hot summer, this problem is even more prominent.In addition, if your machine uses a CPU with large calories such as AMD or P4, you should pay more attention to the heat dissipation problem.The following are several methods to solve the problem of heat dissipation:
1. Try to avoid continuous long -term burning;
2. Turn on the case during record;
3. If possible, it is best to be carried out in an environment with air conditioning.
7. Keep the burning lava clean
During the record, the laser head of the CD -ROM recorder can "write" the information by laser the laser with a higher power of the plate.Therefore, whether the laser head cleaning is a pivotal effect on the benchmarking or failure.Because the dust falling on the laser head may occur slightly sintering under the strong irradiation of the laser beam.Therefore, if you use ordinary cleaning disks to clean at this time, the effect is often not satisfactory and because the inside of the recorder is more precise, it is obviously not stable if it is cleaned by itself.Therefore, the best way is to keep the surrounding environment clean!