Ribbons are the main consumables of needle printers. In daily use, can we extend the life of the strap? The answer is yes.Develop the distance from the distance between the paper to the distance from the thickness of the paper.Let ’s take a look with Xiaobian.
Printmaker color belt maintenance
1. We must learn to keep the printers ribbon "forever".
2. We must be proficient in operating paper thickness regulator to ensure that the printers print head and the surface of the printing paper are always at a suitable distance.
3. When using a printer, learn to "perform surgery" for the straps.
4. We need to learn to supplement the "energy" to the printers ribbon.That is, the ink on the printer color.
How long can I use the color zone of the needle?
First of all, it is necessary to see what model your needle printer is, and then how long it can be used, because different types of machine ribbons are different, and the color bands are long and short.Generally, if the amount of printing is not very large, you can count 1M1 days.This is almost the same. In fact, the strap cannot be calculated by time.To calculate according to your usage.As long as the ribbon is used, the printed words are a bit light, or the ribbon is hairy or broken, then this color strap cannot be used.The ribbon is a dyeing cloth, but the material is also good or bad. A good ribbon can be used for a long time.
1. The service life of the ribbon depends on: the printing rate of printing text cannot be generalized, and the size of the roll paper is not uniform.
2. The ribbon is also divided into the original ribbon and compatible ribbon. The quality of the quality will affect the printing volume.
3. The general check method, see if the strap is pale and faded in the place where the needle printing machine printing machine is printed. It can be seen compared with the two sides.
How to extend the service life of the ribbon
1. Change the ribbon by yourself
A open the printer cover, and you will see a black box (generally black) like a clip. We call it a printing frame. The part of the middle empty part is the printed head.Remove the printing frame, pay attention to pulling up from the end of the print head when disassembling, and the printing frame can be easily removed.
B you can open the printing frame. Because the structure of the printing frames of different models of the printer is different, its ribbon winding method is slightly different, so you must observe the winding method of the primary strap, otherwise the ribbon is likely to be very likelyIt cannot rotate normally and cause printing.It should be noted that the two gears in the printing frame should be clamped with straps, and they should be parallel to them, otherwise it will cause the ribbon to shift with the rotation of the gear.
C card can not rotate.After the ribbon is installed, the printing rack is installed back to the original position, and the color band program can be completed.
2. A good way to extend the needle of the needle
A prepare two printed color boxes, print the formal manuscript with darker (newly replaced) ribbon, and use the color lighter (used, but the belt must be intact, otherwise it will damage the needle)The ribbon prints informal manuscripts or wax paper.
B Fix two small pieces of foam with transparent tape in the outlet position in the color band box, clamp the color band between the two foams, and allow the foam to suck some good quality printing ink. This can keep the ribbon moist.Extend the time of the ribbon.
C uses two pieces of foam with a good quality printing ink to pinch a ribbon exposed by the front end of the box, gently rotate the shaft of the color band, and add some ink for a period of time (with the base) ribbon.(The whole strands must be added, otherwise the color shades are different when printing), and then open the color tape to let the strap with the ink be used to use a small amount of gasoline in the ink). Try a few pages first.Informal drafts make the ink distribution evenly.Print the official draft again.
D Fedation is based on the habit of printing heads from the thickness of the paper.The principle is that it can be large and large, as long as the printing effect meets the requirements.For the new ribbon, you can also adjust the distance appropriately when printing thin paper, because the color is strong at this time, which can ensure the quality of printing.
E can remove the strap when printing wax paper.Do not print the wax paper directly to prevent the wax from melting into the pinhole.Most wax paper is equipped with transparent paper, and it can be printed on the wax paper.
F Sometimes the coloring band roll is not spiritual, and the printing needle repeatedly prints a certain part of the color, causing the color band to be "loopholes".It is caused by the card color with the loose band).For the damaged color zone, you can cut the hole and implement the "welding".The "welding" method is simple: the interface is aligned with a slightly overfuration, and the transparent thin tape is tight (Note: in the inner side) on the inside.Needle (generally only one section in the middle).Based on the quality of the ribbon and the specific situation after printing, I adopt the above methods. Usually, the use time of a ribbon can be extended by 1.5 to 2.5 times, which greatly reduces the consumption of the strap.
3. What should I pay attention to when using the ribbon
A do not use inferior ribbons. Using inferior color band boxes and ribbons, during the printing process, the combination of the lid of the inferior ribbon with the box body is not tight.The gear bite is not tight to relax the color.Due to the poor quality of the ribbon used, the ribbon ink will enter the print head joint and solidify along the printed needle guide hole, resulting in an increased resistance of the print head needle, which can easily cause a broken needle or compress the printing needle, which is more serious.It will cause the printing needle driver chip or color band motor and driving chip to burn.
The installation of b ribbon should be very reasonable. If it is unreasonable, then the ribbon on both sides of the printed head on both sides of the printed head will reverse, entangle, and run off, which will cause the printing needle to directly contact the roller and wear the printing needle, causing faults such as broken needles.